BiGGie's Build

[BiGGiePauls33]

Another small update over here. Picked up the ADJ 15 amp rocker switch and installed into the cabinet. Toggle 1 is my return pump for now until the controller gets hooked up. Toggle 2 is for my first Tunze 6095 running a wave program, toggle 3 is for my second Tunze 6095 running a full stream. The 2 heaters will remain on their own dedicated circuit. I plan on adding another 2 to 3 Tunze's in the future for the 100 gallon, these will also be plugged in here. Tomorrow at some point will be wire management and the routing of the RoDi line from the top off container to the barrels in the other room. Stay tuned

 

[FishieBusiness]

Coming along very nicely. Your putting together a great looking system.

 

[Cpage101]

looking good!

 

[BiGGiePauls33]

Got the ATi 48" 8 bulb hung today. What a PITA with a back injury. Down for the count for the remainder of today.

 

[Chris A.]

So jelly

 

[BiGGiePauls33]

Coming along very nicely. Your putting together a great looking system.

Thanks brah

 

[BiGGiePauls33]

Came up with this chicken scratch sketch the other night while not being able to sleep.

Cutout a divider panel and some center support for the weight from the tank above

Plans are to have two shelves below the power strip. Top shelf will hold the Profilux P4 and the under that will hold the KH Director and associated doser. This will leave a decent space below for some containers and such.

10 gallon Trigger ATO container and Geo Reef Calcium Reactor will be to the right of the partition. Couple coats of gloss white paint, some fasteners and then on to the rockwork.

 

[BiGGiePauls33]

Almost like I actually knew what I was doing.

 

[CAPSLOCK]

So organized.

I could give someone an aneurysm if I posted a photo of my wiring rat's nest...

 

[BiGGiePauls33]

So organized.

I could give someone an aneurysm if I posted a photo of my wiring rat's nest...

lol, trust me I know the feeling. You should see under my office/gaming desk.

 

[FishieBusiness]

Great planning leads to Great success. Love it Paul.

My nest below

 

[afboundguy]

So organized.

I could give someone an aneurysm if I posted a photo of my wiring rat's nest...

You and me both!!!! I wish I could be that organized under my tank!!!

 

[BiGGiePauls33]

Found the only real estate to install the power bar 6e. Hopefully, I get out of the house tomorrow for some cable management supplies.

 

[Zirky]

I love the chicken scratch drawing. I have enough to fill an encyclopedic. when you can’t sleep it the best time to focus your thoughts.

 

[coralfishreef]

I love the chicken scratch drawing. I have enough to fill an encyclopedic. when you can’t sleep it the best time to focus your thoughts.

The drawing and the end result look the same. Pretty good chicken scratch planning. ::thumbs up::

 

[this is me]

How big is the ATO tank?

 

[BiGGiePauls33]

How big is the ATO tank?

Dimensional or capacity? 10 x 16 x 15 or 10 gallons. Currently evaporating about about 1 to 1.5 gals a day with ac running constantly. I'm sure it'll be a lot more once the new tank is wet. After I get the CaRx in place, I may go bigger or just eliminate and plumb directly from fresh water barrel.

 

[this is me]

How big is the ATO tank? I asked because it doesn’t look to be sizable for 1.5gal a day of evaporation. I’d go for the larger barrel outside the stand.

 

[BiGGiePauls33]

How big is the ATO tank? I asked because it doesn’t look to be sizable for 1.5gal a day of evaporation. I’d go for the larger barrel outside the stand.

Originally I bought it for another tank and scratched that tank for the one above.

 

[this is me]

Almost like I actually knew what I was doing.
View attachment 147796

Are you concerned with humidity getting into these valuable electronics?
Is there a way to cut the back open a little and/or add in a fan?